| Rated Voltage (MAX) | 50V | | |
| Rated Current (MAX) | 0.5A [AC/DC (Virtual value) 50Hz] | | |
| Ambient Temperature Range | -45 +85 | | |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | |
| Insulation Resistance | 500 M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal
or ground. | |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1
minute between adjacent terminal or ground. | |
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC at the speed rate of
253mm/minute. Suitable for 0.3mm thick FFC. | |
| Withdrawal Force | 0.49*n (N) MIN | Insert and extract applicable FFC at the speed rate of
253mm/minute. Suitable for 0.3mm thick FFC. | |
| Terminal/Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 253mm per minute. | |
| Repeated Insertion and Withdrawal | Contact Resistance 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate
of less than 10 cycles/minute. No power. | |
| Temperature Rise | 30 MAX | Carrying rated current load. (UL 498) | |
| Vibration | Contact Resistance 60 m MAX; Discontinuity 1 ms MAX. Appearance: No
Damage. | DC 1mA energized. Amplitude: 1.5mm P-P. Sweep time: 10-55-10Hz/min.
Duration: 2 hours in each X,Y,Z axes. | |
| Shock | Discontinuity 1 ms MAX. Appearance: No Damage. | 490m/s {50G}, 3 strokes in each X,Y,Z axes. DC 1mA energized. | |
| Heat Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | 852, 96 hours. Then return to room temperature for 1-2 hours. Mate
applicable FPC/FFC. | |
| Cold Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | -402, 96 hours. Then return to room temperature for 1-2 hours. Mate
applicable FPC/FFC. | |
| Humidity | Contact Resistance 60 m MAX. Insulation Resistance 20 M MIN.
Appearance: No Damage. | Temperature: 402. Relative Humidity: 90-95%. Duration: 96 Hours.
Mate applicable FPC/FFC. | |
| Temperature Cycling | Contact Resistance 60 m MAX. | 5 cycles of: a) -452 for 30 minutes, b) 852 for 30 minutes.
Transition time 10-15 minutes. Mate applicable FPC/FFC. | |
| Salt Spray | Contact Resistance 60 m MAX. Appearance: No Damage, Corrosion. | 484 hours exposure to a salt spray from the 51% solution at 352.
Post-test wash with deionized water and dry at room temperature.
Mate applicable FPC/FFC. | |
| SO2 Gas Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | 24 hours exposure to 505ppm SO2 gas at 402. Mate applicable
FPC/FFC. | |
| NH3 Gas Resistance | Contact Resistance 60 m MAX. Appearance: No Damage. | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia
solution. Mate applicable FPC/FFC. | |
| Solderability | Solder Wetting 95%. | Soldering Time: 20.5 sec. Soldering Temperature: 2355. 0.2 mm from
terminal tip. | |
| Resistance to Soldering Heat | Appearance: No Damage, Deformation. | Soldering Time: 50.5 sec. Soldering Temperature: 2605. 0.2 mm from
terminal tip. | |
