| RATINGS |
| Rated Voltage (MAX) | 50V [AC/DC (Virtual value) 50Hz] | |
| Rated Current (MAX) | 0.5A | |
| Ambient temperature Range | -25+85 | |
| PERFORMANCE - Electrical Performance |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent
terminals or ground. |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (Virtual value) for 1
minute between adjacent terminals or ground. |
| PERFORMANCE - Mechanical Performance |
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC at the speed rate of
253mm/minute. (0.3mm thick FFC) |
| Withdrawal Force | 0.49*n (N) MIN |
| Terminal / Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 25 3mm per minute. |
| PERFORMANCE - Environmental Performance and Others |
| Repeated Insertion and Withdrawal (Contact Resistance) | 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate
of less than 10 cycles/minute. |
| Temperature Rise (Rated Current) | 30 MAX | Carrying rated current load. (UL 498) |
| Vibration (Contact Resistance) | 60 m MAX | Amplitude: 1.5mm P-P Sweep time: 10-55-10Hz in 1 minute Duration: 2
hours in each X.Y.Z. axes. DC 1mA energized. |
| Vibration (Discontinuity) | 1 ms MAX. |
| Shock (Discontinuity) | 1 ms MAX. | 490m/s {50G}, 3 strokes in each X.Y.Z. axes. DC 1mA energized. |
| Heat Resistance (Appearance) | No Damage | 852, 96 hour. Mate applicable FPC/FFC. |
| Heat Resistance (Contact Resistance) | 60 m MAX | 852, 96 hour. Mate applicable FPC/FFC. |
| Cold Resistance (Appearance) | No Damage | -402, 96 hour. Mate applicable FPC/FFC. |
| Cold Resistance (Contact Resistance) | 60 m MAX | -402, 96 hour. Mate applicable FPC/FFC. |
| Humidity (Appearance) | No Damage | Temperature: 402 Relative Humidity: 90-95% Duration: 96 Hours. Mate
applicable FPC/FFC. |
| Humidity (Contact Resistance) | 60 m MAX |
| Humidity (Dielectric Strength) | Must meet 4.1.3 |
| Humidity (Insulation Resistance) | 20 M MIN | 402, 90-95% RH, 96 hours. Mate applicable FPC/FFC. |
| Temperature Cycling (Appearance) | No Damage | 5 cycles of: a) -553 30 minutes b) 852 30 minutes. Mate applicable
FPC/FFC. |
| Temperature Cycling (Contact Resistance) | 60 m MAX |
| Salt Spray (Appearance) | No Damage, Corrosion | 48 4 hours exposure to a salt spray from the 51% solution at 352.
Mate applicable FPC/FFC. |
| Salt Spray (Contact Resistance) | 60 m MAX | 48 4 hours exposure to a salt spray from the 51% solution at 352.
Mate applicable FPC/FFC. |
| SO2 Gas (Contact Resistance) | 60 m MAX | 24 hours exposure to 505ppm. SO2 gas at 402. Mate applicable
FPC/FFC. |
| NH3 Gas (Appearance) | No Damage | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia
solution. Mate applicable FPC/FFC. |
| NH3 Gas (Contact Resistance) | 60 m MAX |
| Solder Ability (Solder Wetting) | 95% or more wetting area | Soldering Time: 20.5 sec. Soldering Temperature: 2455. 0.2 mm from
terminal tip. |
| Resistance to Soldering Heat (Appearance) | No Damage, Deformation | Soldering Time: 305 sec. Soldering Temperature: 2455. At least 5
times. |
