| Ratings |
| Rated Voltage (MAX) | 50V [AC/DC(Virtual value)50Hz] | |
| Rated Current (MAX) | 0.5A | |
| Ambient Temperature Range | -25+85 | |
| Electrical Performance |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal
or ground. |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1
minute between adjacent terminal or ground. |
| Mechanical Performance |
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC at the speed rate of
253mm/minute. (n=number of positions) |
| Withdrawal Force | 0.49*n (N) MIN | Insert and extract applicable FFC at the speed rate of
253mm/minute. (n=number of positions) |
| Terminal / Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 25 3mm per minute. |
| Environmental and Other Performance |
| Repeated Insertion and Withdrawal | Contact Resistance: 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate
of less than 10 cycles/minute. |
| Temperature Rise | 30 MAX | Carrying rated current load. (UL 498) |
| Vibration | Contact Resistance: 60 m MAX; Discontinuity: 1 ms MAX. | Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz in 1 minute; Duration:
2 hours in each X.Y.Z. axes; DC 1mA energized. |
| Shock | Appearance: No Damage; Discontinuity: 1 ms MAX. | 490m/s{50G}, 3 strokes in each X.Y.Z. axes; DC 1mA energized. |
| Heat Resistance | Appearance: No Damage; Contact Resistance: 60 m MAX | 852, 96 hours; Mate applicable FPC/FFC. |
| Cold Resistance | Appearance: No Damage; Contact Resistance: 60 m MAX | -402, 96 hours; Mate applicable FPC/FFC. |
| Humidity | Appearance: No Damage; Contact Resistance: 60 m MAX; Dielectric
Strength: Must meet 4.1.3; Insulation Resistance: 20 M MIN | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours;
Mate applicable FPC/FFC. |
| Temperature Cycling | Appearance: No Damage; Contact Resistance: 60 m MAX | 5 cycles of: a) -553 30 minutes b) 852 30 minutes; Mate applicable
FPC/FFC. |
| Salt Spray | Appearance: No Damage, Corrosion; Contact Resistance: 60 m MAX | 48 4 hours exposure to a salt spray from the 51% solution at 352;
Mate applicable FPC/FFC. |
| SO2 Gas Resistance | Contact Resistance: 60 m MAX | 24 hours exposure to 505ppm SO2 gas at 402; Mate applicable
FPC/FFC. |
| NH3 Gas Resistance | Appearance: No Damage; Contact Resistance: 60 m MAX | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia
solution; Mate applicable FPC/FFC. |
| Solderability | Solder Wetting: 95% of area | Soldering Time: 20.5 sec; Soldering Temperature: 2455; 0.2 mm from
terminal tip. |
| Resistance to Soldering Heat | Appearance: No Damage, Deformation | Soldering Time: 305 sec; Soldering Temperature: 2455; At least 5
times. |
