| RATING |
| | | DC5V 3A |
| PRACTICAL TEMPERATURE RANGE |
| | | -25~85C |
| STANDARD ATMOSPHEIC CONDITIONS |
| (1) Temperature | | 5C TO 35 |
| (2) Humidity | | 45% TO 85% |
| (3) Pressure | | 86Kpa TO 106Kpa |
| MECHANICAL |
| 1. CONNECTION FORCE | After connecting and disconnecting using standard plug gauge 3
times. | | 0.5-1.5Kgf |
| 2. DISCONNECTION FORCE | After connecting and disconnecting using standard plug gauge 3
times. | | 0.8-1.5Kgf |
| 3. TERMINAL STRENGTH | A static load of 0.1N/m(1kgf/cm) applied to the tip of the terminal
for 1 min in any direction. No damage such as cracks, looseness or
play. | | Satisfied mechanical and electrical characteristics. |
| ELECTRICAL |
| 3.1 CONTACT RESISTANCE | Measured at small current (100mA or less) at 1000Hz. | | 40m MAX |
| 3.2 INSULATION RESISTANCE | Apply a voltage of 100V DC for 1 min to following portions: (1)
Between body and conductor (2) Between conductors not to be contact
(3) Between conductors not to be when plug is inserted. | | 100M MIN |
| 3.3 DIELECTRIC STRENGTH | AC 100V rms(50~60Hz) for 1 min, trip current: 0.5mA. (1) Between
body and conductor (2) Between conductors not to be contact (3)
Between conductors not to be when plug is inserted. | | Without damage to parts, arcing or breakdown etc. |
| DURABILITY |
| 4.1 SOLDERABILITY TEST | The top of the terminals shall be dipped 1mm in the solder bath of
2505 for 50.5 seconds. | (1) Solder wetting time | 3 SEC |
| | (2) The area of soldering | > 75% |
| 4.2 RESISTANCE TO SOLDERING HEAT TEST (REFLOW SOLDERING) | Preheat: Temperature on the copper foil surface should reach 180.
Tallest temperature: Temperature on the copper foil surface should
reach the peak temperature of 2605 within 20 seconds. | | Without deformation of case or excessive looseness of terminals.
Electrical characteristics shall be satisfied. |
| 4.2 RESISTANCE TO SOLDERING HEAT TEST (SOLDERING IRON METHOD) | Bit temperature 3305, application time of soldering iron 30.5 sec.
However, excessive pressure shall not be applied to the terminal. | | Without deformation of case or excessive looseness of terminals.
Electrical characteristics shall be satisfied. |
| 4.3 HUMIDITY TEST | Stored at a temperature of 402 and a humidity of 90%to 96% for 96
Hr, then maintained at standard atmospheric condition for 1 Hr. | | Appearance no abnormal. Mechanical and electrical characteristics
shall be satisfied. |
| 4.4 HEAT TEST | Stored at a temperature of 702 for 96 hours, then subjected to
controlled recovery for 1 Hr. | | Appearance no abnormal. Mechanical and electrical characteristics
shall be satisfied. |
| 4.5 COLD TEST | Stored at a temperature of -253 for 96 hours, then subjected to
controlled recovery for 1 Hr. | | Appearance no abnormal. Mechanical and electrical characteristics
shall be satisfied. |
| 4.6 LIFE TEST (WITHOUT LOAD) | Connection and disconnection made with mating plugs and jacks for
5000 cycles at a speed of 10 to 25 cycles/min. | | Satisfied mechanical and electrical characteristics. |
| 4.6 LIFE TEST (LOAD) | At rating condition (non-inductive load), connection and
disconnection made for 5000 cycles at a speed of 10 to 20
cycles/min. | (1) Contact resistance | 0.1 |
| | (2) Disconnection force | 0.8 TO 2.0N |
| | (3) Other | Satisfied mechanical and electrical characteristics. |
| 4.7 TEMPERATURE CYCLING TEST | Subjected to 5 cycles of specified conditions, then returned to
room ambient for 30 minutes. | Insertion & Extraction Force: | 3 TO 20N |
| | Contact Resistance: | MAX.30M |
| | Insulation Resistance: | MIN.100 M |
| | Dielectric Withstanding Voltage: | 100VAC/MIN (Between Terminals) |
| | | Product cannot deform or crack. |
| 4.8 COLD & HEAT SHOCK TEST | Subjected to 5 cycles of specified conditions, then returned to
room ambient for 30 minutes. | Insertion & Extraction Force: | 3 TO 25N |
| | Contact Resistance: | MAX.30M |
| | Insulation Resistance: | MIN.100 M |
| | Dielectric Withstanding Voltage: | 500VAC/MIN (Between Terminals) |
| | | Product cannot deform or crack. |
