KO Consolidation Apparatus

KO Consolidation Apparatus

Model BTU-STC-KO

Description

This equipment is a KO consolidation apparatus, modelBTU-STC-KO, used to determine thecoefficient of earth pressure at rest (K₀)of soil specimens with a diameter of Ø61.8 mm. The lateral pressure under no lateral strain conditions is measured using a pore pressure meter (or lateral pressure sensor). It is mainly used to study the compression characteristics of soil under lateral restraint, providing K₀ values for settlement calculations and earth pressure analysis.

System overview: The KO consolidation apparatus is used to determine the coefficient of earth pressure at rest for Ø61.8 mm soil specimens. The lateral pressure can be measured by a pore pressure meter.

Test Standards (International)

• ASTM D2435(One‑dimensional consolidation – K₀ conditions can be derived)
• ASTM D4186(CRS consolidation – K₀ measurement possible)
• ASTM D4767(Triaxial compression – K₀ consolidation stage)
• ISO 17892‑5(Consolidation test)
• BS 1377‑6(Consolidation test)
• Chinese GB/T 50123‑2019(Standard for soil test methods – includes K₀ test)

The equipment can meet the requirements of these standards for lateral pressure measurement, axial loading, displacement measurement, etc.

Specification

Note: The screenshot does not specify maximum axial pressure, loading method (lever/servo), lateral pressure sensor range, accuracy, etc. – refer to the product manual.

Detail

• K₀ consolidation principle– Under fully lateral restraint (zero lateral strain), axial pressure is applied to the specimen and the lateral pressure(σ h)is measured. The coefficient of earth pressure at rest is K₀ = σ_h / σ_v.
• Specimen size– Diameter 61.8 mm, height 40 mm (height‑to‑diameter ratio ≈0.65, common for K₀ consolidation tests).
• Axial displacement measurement– Range 12.7 mm, resolution 0.01 mm (10 μm), allowing precise compression recording.
• Pressure cell seal– No leakage at rated pressure, volume change <0.20 ml (very small volumetric change, ensuring lateral rigidity).
• Lateral pressure measurement– Using a pore pressure meter (connected to a lateral pressure sensor or liquid pressure sensor).
• Suitable materials– Fine‑grained soils (clay, silty clay), commonly used for saturated soil K₀ determination.

Application

• Foundation settlement calculation– K₀ values are used for settlement estimation of normally consolidated and overconsolidated soils (e.g., K₀ consolidation test method).
• Earth pressure calculation– K₀ is needed for calculating earth pressure at rest on retaining walls, basement walls, etc.
• Constitutive model parameters– Provides K₀ parameter for models such as Modified Cam Clay.
• Laboratory testing– Research institutions and university soil mechanics laboratories.
• Numerical model validation– Provides laboratory K₀ values for calibrating finite element models.

Advantages

• Specialised K₀ consolidation– Dedicated design for measuring the coefficient of earth pressure at rest, compact structure.
• High‑precision displacement measurement– 0.01 mm resolution, meeting consolidation deformation accuracy requirements.
• Good sealing– Pressure cell volume change <0.20 ml, ensuring lateral restraint (approximate zero lateral strain).
• Easy operation– Lateral pressure can be measured directly with a pore pressure meter.
• Standard specimen size– Ø61.8 mm is a common size, facilitating sample preparation and comparison.
• Compatibility– Can be used with various loading systems (lever, servo, etc., to be supplied separately).

What To Choose

Select this equipment or compare with other configurations based on testing requirements:

Process Flow

Example:Standard K₀ consolidation test (step loading, saturated clay)

• Specimen preparation
  • Cut undisturbed or remoulded clay specimen using a Ø61.8×40 mm ring.
  • Saturate (vacuum or back pressure saturation), measure initial water content and density.

• Specimen installation
  • Place the specimen into the pressure cell of the K₀ consolidometer, with porous stones above and below.
  • Install the axial displacement sensor (zero it).
  • Connect the lateral pressure measurement system (pore pressure meter or lateral pressure sensor) and de‑air the pressure cell.
  • Position the pressure cell in the loading frame (e.g., a separate consolidometer main frame).

• Apply initial seating pressure
  • Apply a small axial pressure (e.g., 5 kPa) and record initial axial displacement and lateral pressure.

• Set test parameters
  • Define the load sequence (e.g., 25, 50, 100, 200, 400, 800 kPa).
  • Duration for each load step is typically 24 hours or until consolidation is stable (displacement change <0.01 mm per hour).
  • Set data acquisition intervals (e.g., 0.1, 1, 10, 60 minutes).

• Start the test
  • Apply the first axial load step.
  • Record axial displacement and lateral pressure in real time.
  • At each load step, after axial displacement stabilises, record the lateral pressure.

• Calculate K₀
  • For each load step, K₀ = lateral pressure(σh)/axial pressure(σv).
  • Plot K₀ vs. σ_v curve.

• End and disassembly
  • After the test, unload, remove the specimen.
  • Clean the pressure cell and sensors.

• Data processing
  • Calculate K₀ values for each load step; take the average or analyse the trend.
  • For normally consolidated soils, K₀ ≈ 1 – sin φ′ (Jaky’s formula) can be used for verification.
  • Generate a test report.

If the equipment is paired with aservo loading system, it can perform CRS or automatic step loading with real‑time lateral pressure acquisition, improving efficiency.

Summary:The BTU-STC-KO is a dedicated K₀ consolidation apparatus for determining the coefficient of earth pressure at rest of Ø61.8×40 mm soil specimens. It features an axial displacement resolution of 0.01 mm and a well‑sealed pressure cell (volume change <0.20 ml). Lateral pressure is measured via a pore pressure meter or lateral pressure sensor. It is suitable for foundation settlement calculations, earth pressure analysis, and constitutive model parameter determination. Note that the loading system (e.g., a consolidometer load frame) must be supplied separately; if high‑precision automatic loading is needed, a servo system can be added. The apparatus is designed for fine‑grained soils only, with a fixed specimen size.

260 workers, 25000 ㎡ non-dust workshop, 16 years experience, SGS & INTERTEK certificated, one hour reach Tianjin port, this is how we keep good quality and competitive prices for global valued customers.

Our main products cover Universal testing machine, Compression testing machine, Soil,Concrete,Cement Mortar,Aggregates Rocks, Asphalt Bitumen, NDT,Pavement ,Paint,Ceramics,Drilling Fluids, Geotextiles, Textiles, Environmental,General Equipment.BTUTEST is exporting its products to more than 60 countries by offering its services through its authorized distributors and representatives.

Our main customers are private and research testing laboratories, road and general contractors, concrete and cement manufacturers, asphalt manufacturers, government authorities, ministries, engineers, consultants and re-seller. We also cooperate with accredited research centers and the most important universities in the world.we can supply more top quality product and service for more customer’s.