|230V - 240V , 50Hz|
|No load speed||2850 / min|
|40L collection box|
|Induction motor ( AL winding )|
|Cable||H05VV-F 2 x 1.0mm2 with VDE plug, length : 35cm|
Electric Lawn mower RY-3033 is1300W,it can also be replaced withe other
input power , because different input power , so the model will be
|0ther modle||lnput power|
The choice can be made according to the company and customer needs lnput power
Operate the mower correctly :
1 . Wear long-sleeved top and trousers, no loose clothing, safety
helmet , goggles, earmuffs to avoid noise , non-slippery shoes, no
slippers or bare feet .
2 . Do not operate in hot or cold climate for long periods of time
, there should be appropriate rest time .
3 .Do not allow drunk , cold or sick people , children and people
who are not familiar with the correct operation of the mower .
4 . Refuel the engine after it stops running and cools .
5 . Avoid oil overflow when refueling. If it is spilled, wipe it
6 . The machine should be at least 1 meter away from the object
before starting .
7 .A lawn mower must be used in a well-ventilated outdoor
8 . Before each use must check whether the blade is sharp or worn,
and whether the clutch screw is locked .
9 . As some machine motors have a loud sound , please avoid using
them during the rest time , which may affect the rest of the staff
in the attachment .
Check before starting :
1 . Sharp blade must be replaced without abnormal blade .
2 . Make sure that others are not in the danger area before
starting the engine .
3 . Grasp the operating lever when starting the engine to avoid
losing control due to vibration .
4 . Before starting, make sure that the blade is far away from the
ground and has no contact with other objects .
5 . Make sure to use the spare parts provided by the original
manufacturer, especially the blade .
6 . Check whether the full cover is locked .
matters needing attention for use of mower :
If there is abnormal vibration during operation , the engine must
be stopped immediately .
The machine must be operated with two hands . One hand is not
The side of the muffler should be turned out to avoid burns .
Method of mowing with a lawn mower .
Since the blade is left , the efficient working direction is from
left to right .
The most efficient mowing is to make two - thirds of the blade
diameter cut into weeds .
Caution is required after operation .
1 . Wrap the blade after use to avoid accidental injury to others
2 . Make sure the blade stops completely before cleaning and
3 . Remove the spark plug wire to avoid accidental fire .
4. Wait until the engine is completely cooled before storage .
Keep the machine in a cool, dry place and keep it out of children's
6 . Lubricate the gear box every 25 hours or 3 1/2 days, and
lubricate the inner and outer pipe .
7 . Clean muffler and drum every 100 hours or 15 days .
8 . Butter the blade when not in use for a long time to avoid
rusting the blade .
9 . After use, the blade should be placed in the place beyond
children's reach .
1 . A series of checks and preparations must be made before the
mower is placed on the ground . Stop the machine on the horizontal
position, check whether the tire pressure is normal , timely aerate
when t is nsufficient , check whether the cutting disc is running
normally , check whether the cutter is intact , all transmission
belts should be free of cracks , the pressure belt wheel should
work effectively , otherwise, it should be replaced or adjusted in
time .Put the clutch handle of the gearbox and the cutter in the
separate position, the gear handle in the neutral position, the
pressure belt wheel of the cutterloosen and put it in the walking
position, put the throttle handle in the middle position , start
the engine with a crank, slowly increase the throttle after
starting , and push the clutch handle to the joint position .Then
it is connected to the low speed gear , and the lawn mower starts
to walk . When working close to the village, the lawn mower can
walk to the destination by itself , because the speed of this lawn
mower is relatively slow, and if the distance is relatively long ,
there should be a means of transport .
2 . When the mower comes to the working area, move the cutter
pressure belt wheel to the working position . Adjust the cutter
according to the stubble height requirement . Adjust the height of
the cutter mainly by adjusting the position of the two
screws.Tighten the connecting screw of the blade on the cutter
plate and tighten the connecting screw on the protective cover.Put
both clutches in separate positions , hang in neutral position,
restart the engine , slowly increase the throttle , slowly connect
the cutter clutch handle, the cutting disc begins to work , combine
the gearbox clutch , and then connect to the low gear, and the
mower begins to work .
Operation process of lawn mower :
1 . This small lawn mower is relatively simple to operate in the
operation . First , the operation pa selection is relatively
flexible , because the turning radius of the machine is small and
there is no flexibility, because the turning radius of the machine
is small and there is no walking dead Angle .Generally , the lawn
mower is allowed . When the local surface is uneven and the forage
density is high, choose the low speed gear; otherwise , choose the
high speed gear . During the working process , the two clutch
tensioning wheel handles are always in the joint position , because
during the working process , when the engine is running at high
speed , it is easy to damage the machine by joining or separating
the tensioning wheel handles . Therefore, the operator does not
need to move the two handles in the process of mowing . The
operation process is relatively simple , and the driver only needs
to hold the handle to control the walking route of the mower .
2 . During the operation, the terrain should be carefully observed
at any time in front of the operation . In case of large pits and
high hills , slow down and make a detour , otherwise the high-speed
cutting knife will hit a lot of dust, which is not good for the
operator and the machine . This machine is only suitable for slope
work below 25 degrees . If the slope is too large, the lubricating
oil cannot be lubricated to all the moving parts, and the engine
will be damaged after long-time operation . When the machine is
working, it should keep irrelevant personnel away from the lawn
mower , and avoid the small stone that the cutter rolls to hurt
1 . High efficiency: generally, each mower can mow more than 8 x
667 m2 per day, and its efficiency is 16 times that of manual
2 . Good benefi t: due to the fast rotation speed of the mower ,
the cutting effect of orchard weeds is good, especially for weeds
with high tenderness. In general, three times a year weeding ,
basically meet the requirements of weeding .
3 . Soil and water conservation: artificially use a hoe to hoe the
grass. Because the surface soil is loosened at the same time, soil
and water loss is often caused. The use of lawn mower, because only
cut out the grass on the ground part, the soil surface has little
impact, and the roots of soil cementation, is very beneficial to
soil and water conservation .
4 . Increase fertility: use a lawn mower to cut the weeds until
they reach a certain height. A large number of weeds can be cut to
cover the orchard .